diff options
Diffstat (limited to 'keyboards/phantom')
| -rw-r--r-- | keyboards/phantom/Makefile | 74 | ||||
| -rw-r--r-- | keyboards/phantom/config.h | 91 | ||||
| -rw-r--r-- | keyboards/phantom/keymaps/default/keymap.c | 169 | ||||
| -rw-r--r-- | keyboards/phantom/led.c | 43 | ||||
| -rw-r--r-- | keyboards/phantom/phantom.c | 9 | ||||
| -rw-r--r-- | keyboards/phantom/phantom.h | 40 | ||||
| -rw-r--r-- | keyboards/phantom/pinout.jpg | bin | 0 -> 86118 bytes | |||
| -rw-r--r-- | keyboards/phantom/pinout.txt | 1 |
8 files changed, 427 insertions, 0 deletions
diff --git a/keyboards/phantom/Makefile b/keyboards/phantom/Makefile new file mode 100644 index 0000000000..3a71fd0ee3 --- /dev/null +++ b/keyboards/phantom/Makefile @@ -0,0 +1,74 @@ + + +SRC = led.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID + + +ifndef QUANTUM_DIR + include ../../Makefile +endif diff --git a/keyboards/phantom/config.h b/keyboards/phantom/config.h new file mode 100644 index 0000000000..d5878766f0 --- /dev/null +++ b/keyboards/phantom/config.h @@ -0,0 +1,91 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0003 +#define MANUFACTURER PHANTOM +#define PRODUCT PHANTOM RGB MOD +#define DESCRIPTION QMK keyboard firmware for PHANTOM TKL + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 17 + +// ROWS: Top to bottom, COLS: Left to right +/* Row pin configuration +*/ +#define MATRIX_ROW_PINS { B5, B4, B3, B2, B1, B0 } +/* Column pin configuration + */ +#define MATRIX_COL_PINS { D5, C7, C6, D4, D0, E6, F0, F1, F4, F5, F6, F7, D7, D6, D1, D2, D3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION ROW2COL + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* Underlight configuration + */ + #define ws2812_PORTREG PORTE + #define ws2812_DDRREG DDRE + #define ws2812_pin 2 + #define RGBLED_NUM 20 // Number of LEDs + #define RGBLIGHT_HUE_STEP 10 + #define RGBLIGHT_SAT_STEP 17 + #define RGBLIGHT_VAL_STEP 17 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/phantom/keymaps/default/keymap.c b/keyboards/phantom/keymaps/default/keymap.c new file mode 100644 index 0000000000..1368226aa9 --- /dev/null +++ b/keyboards/phantom/keymaps/default/keymap.c @@ -0,0 +1,169 @@ +#include "phantom.h" + +#ifdef RGBLIGHT_ENABLE +#include "rgblight.h" +#endif + +// Used for SHIFT_ESC +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-----------------------------------------------------------------------------. + * |Esc |f1| f2| f3| f4| | f5| f6| f7| f8| | f9|f10|f11|f12| |Prnt|ScLk|Paus| + * |-----------------------------------------------------------| |--------------| + * | ~ | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0| - | = |Backsp | | Ins|Home|PgUp| + * |-----------------------------------------------------------| |--------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | Del| End|PgDn| + * |-----------------------------------------------------------| `--------------' + * |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | + * |-----------------------------------------------------------| ,----. + * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift | | Up | + * |-----------------------------------------------------------| ,-------------. + * |Ctrl|Gui |Alt | Space |ALT |GUI |_FL |CTRL | |Lft| Dn |Rig | + * `-----------------------------------------------------------' `-------------' + */ +[_BL] = KEYMAP( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DELETE, KC_END, KC_PGDN, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, \ + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT), + + /* Keymap _FL: Function Layer + * ,-----------------------------------------------------------------------------. + * | | | | | | | | | | | | | | | | | | | | + * |-----------------------------------------------------------| |--------------| + * | | | | | | | | | | | | | | Reset | | | | | + * |-----------------------------------------------------------| |--------------| + * | | | | | | | | | | | | | | | | | | | + * |-----------------------------------------------------------| `--------------' + * | | | | | | | | | | | | | | + * |-----------------------------------------------------------| ,----. + * | | F1| F2| F3| F4| F5|F6 |F7 |F8 | | | | | | + * |-----------------------------------------------------------| ,-------------. + * | | | | | | | | | | | | | + * `-----------------------------------------------------------' `-------------' + */ +[_FL] = KEYMAP( + #ifdef RGBLIGHT_ENABLE + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, \ + KC_TRNS, F(1), F(2), F(3), F(4), F(5), F(6), F(7), F(8), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #else + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #endif +}; + +enum function_id { + SHIFT_ESC, + #ifdef RGBLIGHT_ENABLE + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL + #endif +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_FUNCTION(SHIFT_ESC), + #ifdef RGBLIGHT_ENABLE + [1] = ACTION_FUNCTION(RGBLED_TOGGLE), + [2] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [3] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [5] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [7] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [8] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + #endif +}; + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + static uint8_t shift_esc_shift_mask; + switch (id) { + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + //led operations + #ifdef RGBLIGHT_ENABLE + case RGBLED_TOGGLE: + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + #endif + } +} diff --git a/keyboards/phantom/led.c b/keyboards/phantom/led.c new file mode 100644 index 0000000000..b2459c7743 --- /dev/null +++ b/keyboards/phantom/led.c @@ -0,0 +1,43 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <avr/io.h> +#include "stdint.h" +#include "led.h" + +void led_init(void) { + // * Set our LED pins as output + DDRB |= (1<<6); + DDRB |= (1<<7); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // Turn capslock on + PORTB |= (1<<6); + } else { + // Turn capslock off + PORTB &= ~(1<<6); + } + if (usb_led & (1<<USB_LED_SCROLL_LOCK)) { + // Turn scrolllock on + PORTB |= (1<<7); + } else { + // Turn scrolllock off + PORTB &= ~(1<<7); + } +} diff --git a/keyboards/phantom/phantom.c b/keyboards/phantom/phantom.c new file mode 100644 index 0000000000..d53af491fe --- /dev/null +++ b/keyboards/phantom/phantom.c @@ -0,0 +1,9 @@ +#include "phantom.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); +}; diff --git a/keyboards/phantom/phantom.h b/keyboards/phantom/phantom.h new file mode 100644 index 0000000000..420826becf --- /dev/null +++ b/keyboards/phantom/phantom.h @@ -0,0 +1,40 @@ +#ifndef PHANTOM_H +#define PHANTOM_H + +#include "quantum.h" + +/* Phantom matrix layout + * ,-----------------------------------------------------------------------------. + * |00 |02| 03| 04| 05| | 06| 07| 08| 09| | 0a|0b |0c |0d | |0e |0f |0g | + * |-----------------------------------------------------------| |--------------| + * | 01| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 1a| 1b| 1d | |1e |1f |1g | + * |-----------------------------------------------------------| |--------------| + * |20 | 21| 22| 23| 24| 25| 26| 27| 28| 29| 2a| 2b| 2c| 2d| | 2e | 2f | 2g | + * |-----------------------------------------------------------| `--------------' + * |30 | 31| 32| 33| 34| 35| 36| 37| 38| 39| 3a| 3b| 3d | + * |-----------------------------------------------------------| ,----. + * | 40 | 42| 43| 44| 45| 46| 47| 48| 49| 4a| 4b| 4d | | 4f | + * |-----------------------------------------------------------| ,-------------. + * | 50 | 51 | 52 | 57 |5a | 5b | 5c | 5d | | 5e| 5f | 5g | + * `-----------------------------------------------------------' `-------------' + */ +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ + k00, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, k0g, \ + k01, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1d, k1e, k1f, k1g, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, k2e, k2f, k2g, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, \ + k40, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b, k4d, k4f, \ + k50, k51, k52, k57, k5a, k5b, k5c, k5d, k5e, k5f, k5g \ +) \ +{ \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, k0g}, \ + {k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1d, k1d, k1e, k1f, k1g}, \ + {k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, k2e, k2f, k2g}, \ + {k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, k3d, k3d, k3d, k3d}, \ + {k40, k40, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b, k4d, k4d, k4f, k4f, k4f}, \ + {k50, k51, k52, k57, k57, k57, k57, k57, k57, k57, k5a, k5b, k5c, k5d, k5e, k5f, k5g} \ +} + +#endif diff --git a/keyboards/phantom/pinout.jpg b/keyboards/phantom/pinout.jpg Binary files differnew file mode 100644 index 0000000000..30b0b8bf4b --- /dev/null +++ b/keyboards/phantom/pinout.jpg diff --git a/keyboards/phantom/pinout.txt b/keyboards/phantom/pinout.txt new file mode 100644 index 0000000000..36f044d157 --- /dev/null +++ b/keyboards/phantom/pinout.txt @@ -0,0 +1 @@ +For WS2812B LED strip support, connect DIN from strip to PE2 on Teensy (see reference image pinout.jpg)
\ No newline at end of file |
