diff options
Diffstat (limited to 'keyboards/ergodox/ergodone/rules.mk')
| -rw-r--r-- | keyboards/ergodox/ergodone/rules.mk | 91 |
1 files changed, 91 insertions, 0 deletions
diff --git a/keyboards/ergodox/ergodone/rules.mk b/keyboards/ergodox/ergodone/rules.mk new file mode 100644 index 0000000000..e7fd4e0aba --- /dev/null +++ b/keyboards/ergodox/ergodone/rules.mk @@ -0,0 +1,91 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- + +# # project specific files +SRC = \ + twimaster.c \ + matrix.c \ + expander.c \ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA +USB_6KRO_ENABLE = no # USB 6key Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +KEYMAP_IN_EEPROM_ENABLE = no # External keymap in eeprom +KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor +SOFTPWM_LED_ENABLE = no # Enable SoftPWM to drive backlight +FADING_LED_ENABLE = no # Enable fading backlight +BREATHING_LED_ENABLE = no # Enable breathing backlight +LEDMAP_ENABLE = no # Enable LED mapping +LEDMAP_IN_EEPROM_ENABLE = no # Read LED mapping from eeprom +ONEHAND_ENABLE = no # Disable Onehand +RGBLIGHT_ENABLE = no +MIDI_ENABLE = no |