Merge pull request #2 from jackhumbert/master

Pull from upstream

1 files changed, 112 insertions, 0 deletions

diff --git a/keyboards/gh60/keymaps/robotmaxtron/Makefile b/keyboards/gh60/keymaps/robotmaxtron/Makefile
new file mode 100644
index 0000000000..2e69aee298
--- /dev/null
+++ b/keyboards/gh60/keymaps/robotmaxtron/Makefile
@@ -0,0 +1,112 @@
+#----------------------------------------------------------------------------

+# On command line:

+#

+# make all = Make software.

+#

+# make clean = Clean out built project files.

+#

+# make coff = Convert ELF to AVR COFF.

+#

+# make extcoff = Convert ELF to AVR Extended COFF.

+#

+# make program = Download the hex file to the device.

+#                Please customize your programmer settings(PROGRAM_CMD)

+#

+# make teensy = Download the hex file to the device, using teensy_loader_cli.

+#               (must have teensy_loader_cli installed).

+#

+# make dfu = Download the hex file to the device, using dfu-programmer (must

+#            have dfu-programmer installed).

+#

+# make flip = Download the hex file to the device, using Atmel FLIP (must

+#             have Atmel FLIP installed).

+#

+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer

+#               (must have dfu-programmer installed).

+#

+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP

+#                (must have Atmel FLIP installed).

+#

+# make debug = Start either simulavr or avarice as specified for debugging, 

+#              with avr-gdb or avr-insight as the front end for debugging.

+#

+# make filename.s = Just compile filename.c into the assembler code only.

+#

+# make filename.i = Create a preprocessed source file for use in submitting

+#                   bug reports to the GCC project.

+#

+# To rebuild project do "make clean" then "make all".

+#----------------------------------------------------------------------------

+

+# MCU name

+#MCU = at90usb1287

+MCU = atmega32u4

+

+# Processor frequency.

+#     This will define a symbol, F_CPU, in all source code files equal to the

+#     processor frequency in Hz. You can then use this symbol in your source code to

+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

+#     automatically to create a 32-bit value in your source code.

+#

+#     This will be an integer division of F_USB below, as it is sourced by

+#     F_USB after it has run through any CPU prescalers. Note that this value

+#     does not *change* the processor frequency - it should merely be updated to

+#     reflect the processor speed set externally so that the code can use accurate

+#     software delays.

+F_CPU = 16000000

+

+

+#

+# LUFA specific

+#

+# Target architecture (see library "Board Types" documentation).

+ARCH = AVR8

+

+# Input clock frequency.

+#     This will define a symbol, F_USB, in all source code files equal to the

+#     input clock frequency (before any prescaling is performed) in Hz. This value may

+#     differ from F_CPU if prescaling is used on the latter, and is required as the

+#     raw input clock is fed directly to the PLL sections of the AVR for high speed

+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

+#     at the end, this will be done automatically to create a 32-bit value in your

+#     source code.

+#

+#     If no clock division is performed on the input clock inside the AVR (via the

+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

+F_USB = $(F_CPU)

+

+# Interrupt driven control endpoint task(+60)

+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

+

+

+# Boot Section Size in *bytes*

+#   Teensy halfKay   512

+#   Teensy++ halfKay 1024

+#   Atmel DFU loader 4096

+#   LUFA bootloader  4096

+#   USBaspLoader     2048

+OPT_DEFS += -DBOOTLOADER_SIZE=4096

+

+

+# Build Options

+#   comment out to disable the options.

+#

+BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

+MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

+EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

+# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

+# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

+KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

+# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

+# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

+# MIDI_ENABLE ?= YES		# MIDI controls

+# UNICODE_ENABLE ?= YES		# Unicode

+# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID

+RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow

+

+ifndef QUANTUM_DIR

+	include ../../../../Makefile

+endif

+