Merge branch 'master'

Conflicts:
	keyboards/planck/keymaps/bone2planck/keymap.c

4 files changed, 97 insertions, 83 deletions

diff --git a/keyboards/atomic/Makefile b/keyboards/atomic/Makefile
index 08e9205cbf..4e2a6f00fd 100644
--- a/keyboards/atomic/Makefile
+++ b/keyboards/atomic/Makefile
@@ -1,73 +1,3 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no         # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no            # MIDI controls
-AUDIO_ENABLE ?= no           # Audio output on port C6
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../Makefile
 endif
\ No newline at end of file
diff --git a/keyboards/atomic/keymaps/pvc/keymap.c b/keyboards/atomic/keymaps/pvc/keymap.c
index f16ec8a6ec..b02e89d2c7 100644
--- a/keyboards/atomic/keymaps/pvc/keymap.c
+++ b/keyboards/atomic/keymaps/pvc/keymap.c
@@ -154,7 +154,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 /* UPPER
  * .---------------------------------------------------------------------------------------------------------------------- 2u ------------.
- * | PRINT  | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | NUM LK | /      | *      |        | NUM LK | SCR LK | XXXXXX . PAUSE  |
+ * | PRINT  | BR TOG | BR SP+ | BR SP- | BR RST | XXXXXX | XXXXXX | NUM LK | /      | *      |        | NUM LK | SCR LK | XXXXXX . PAUSE  |
  * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------|
  * |        | F1     | F2     | F3     | F4     |        |        | 7      | 8      | 9      | -      |        |        |        | INS    |
  * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------|
@@ -180,9 +180,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------|
  * |        | $      | {      | [      | (      | %      | #      | )      | ]      | }      | @      |        |        |        | INS    |
  * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------|
- * |        | ^      | *      | +      | -      | ;      | :      | _      | '      | "      | `      |        | XXXXXX .        | HOME   |
+ * |        | ^      | *      | +      | -      | /      | \      | _      | '      | "      | `      |        | XXXXXX .        | HOME   |
  * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ---------------------+--------|
- * |        | |      | &      | !      | ~      | /      | \      | =      | <      | >      | ?      | XXXXXX .        |        | END    |
+ * |        | |      | &      | !      | ~      | ;      | :      | =      | <      | >      | ?      | XXXXXX .        |        | END    |
  * |--------+--------+--------+--------+--------+- 2u ------------+--------+--------+--------+--------+-----------------+--------+--------|
  * |        |        |        |        |        |                 |        |        |        |        |        |        |        |        |
  * '--------------------------------------------------------------------------------------------------------------------------------------'
@@ -191,16 +191,30 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  [LAYER_LOWER]        = { // LOWER
   { _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  ________________  },
   { _______, KC_DLR,  KC_LCBR, KC_LBRC, KC_LPRN, KC_PERC, KC_HASH, KC_RPRN, KC_RBRC, KC_RCBR, KC_AT,   _______, _______, _______, KC_INS   },
-  { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SCLN, KC_COLN, KC_UNDS, KC_QUOT, KC_DQT,  KC_GRV,  _______, ________________, KC_HOME  },
-  { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SLSH, KC_BSLS, KC_EQL,  KC_LT,   KC_GT,   KC_QUES, ________________, _______, KC_END   },
+  { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SLSH, KC_BSLS, KC_UNDS, KC_QUOT, KC_DQT,  KC_GRV,  _______, ________________, KC_HOME  },
+  { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SCLN, KC_COLN, KC_EQL,  KC_LT,   KC_GT,   KC_QUES, ________________, _______, KC_END   },
   { _______, _______, _______, _______, _______, ________________, _______, _______, _______, _______, _______, _______, _______, _______  },
  },
 
+/* FUNCTION
+ * .---------------------------------------------------------------------------------------------------------------------- 2u ------------.
+ * | NUM LK |        |        |        |        |        |        |        |        |        |        |        |        | XXXXXX .        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------|
+ * | SCR LK | F13    | F14    | F15    | F16    |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------|
+ * | CAP LK | F17    | F18    | F19    | F20    |        |        |        |        |        |        |        | XXXXXX .        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ---------------------+--------|
+ * |        | F21    | F22    | F23    | F24    |        |        |        |        |        |        | XXXXXX .        | VOL UP | MUTE   |
+ * |--------+--------+--------+--------+--------+- 2u ------------+--------+--------+--------+--------+-----------------+--------+--------|
+ * |        |        |        |        |        | PLAY/PAUSE      |        |        |        |        |        | PTRACK | VOL DN | NTRACK |
+ * '--------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
  [LAYER_FUNCTION]     = { // FUNCTION
-  { KC_NLCK, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  ________________  },
-  { KC_SLCK, KC_F13,  KC_F14,  KC_F15,  KC_F16,  KC_F17,  KC_F18,  KC_F19,  KC_F20,  KC_F21,  KC_F22,  KC_F23,  KC_F24,  _______, KC_PAUS  },
-  { KC_CAPS, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, ________________, KC_PSCR  },
-  { _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, ________________, KC_VOLU, KC_MUTE  },
+  { KC_NLCK, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXXXXXXXXXXX  },
+  { KC_SLCK, KC_F13,  KC_F14,  KC_F15,  KC_F16,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX  },
+  { KC_CAPS, KC_F17,  KC_F18,  KC_F19,  KC_F20,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXXXXXXXXXXX, XXXXXXX  },
+  { _______, KC_F21,  KC_F22,  KC_F23,  KC_F24,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, ________________, KC_VOLU, KC_MUTE  },
   { _______, _______, _______, _______, _______, KC_MPLY, KC_MPLY, _______, _______, _______, _______, _______, KC_MPRV, KC_VOLD, KC_MNXT  },
  },
 
diff --git a/keyboards/atomic/readme.md b/keyboards/atomic/readme.md
index ab1e7ba1ff..674dcf113b 100644
--- a/keyboards/atomic/readme.md
+++ b/keyboards/atomic/readme.md
@@ -13,13 +13,14 @@ Download or clone the whole firmware and navigate to the keyboards/atomic folder
 Depending on which keymap you would like to use, you will have to compile slightly differently.
 
 ### Default
-To build with the default keymap, simply run `make`.
+To build with the default keymap, simply run `make default`.
 
 ### Other Keymaps
 Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a file in the keymaps folder named `<name>.c` and see keymap document (you can find in top readme.md) and existent keymap files.
 
-To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
+
 ```
-$ make KEYMAP=[default|jack|<name>]
+$ make [default|jack|<name>]
 ```
 Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
diff --git a/keyboards/atomic/rules.mk b/keyboards/atomic/rules.mk
new file mode 100644
index 0000000000..d0f3a3a1c0
--- /dev/null
+++ b/keyboards/atomic/rules.mk
@@ -0,0 +1,69 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+AUDIO_ENABLE ?= no           # Audio output on port C6
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
\ No newline at end of file